TPO SINGLE-PLY ROOF SYSTEMS PRODUCTS
SAVE ENERGY WITH TOPPS WHITE ROOF COATINGS
Often, building managers and roofing contractors decide to turn to roof coatings in order to repair or prevent a problem. However, coating your roof doesn’t only prolong its life. It actually makes your roof a better, more energy-efficient part of your building. White roof coatings can have a substantial impact on the temperature of your building, resulting in significant energy cost savings.
The use of time-tested and climate-proven products like our Topps Seal® white roofing coating, an ENERGY STAR® certified product, dramatically drops the heat island effect of your roof and can result in significant energy savings on cooling bills long into the future. On hot, sunny summer days, the sun can heat up dry, exposed urban surfaces, such as roofs and pavement, to temperatures 50–90°F (27–50°C) hotter than the air.
Not sure where to start? Check out our roof sealant and coatings below to see how we stack up

FLEX FB LOW RISE ADHESIVE
Flex FB Low Rise Adhesive is a two component, low rise polyurethane adhesive designed to attach Flex Fleeceback Roofing Membranes to a variety of approved substrates in accordance with current Flex Roof Details and Specifications.

FLEX THERMOPLASTIC POURABLE SEALER
Flex Thermoplastic One-Part Pourable Sealer is a one-part, moisture curing, elastomeric polyether sealant providing rapid skin time when exposed to atmospheric moisture forming a waterproof rubber surface in less than an hour.

FLEX TPO 6″PRESSURE-SENSITIVE SECUREMENT STRIP
Flex TPO 6 inch Pressure-Sensitive Securement Strip is a nominal 0.045” (1.14mm) thick reinforced TPO membrane strip with a nominal 0.035” (0.89mm) thick, fully cured synthetic rubber pressure sensitive adhesive laminated along one edge.

FLEX TPO 10″PRESSURE-SENSITIVE SECUREMENT STRIP
Flex TPO 10” PS Securement Strip is used in place of half width sheets to secure membrane in the perimeter area of the roof. The use of this product allows field membrane to be utilized over the entire roof area.

FLEX TPO MOLDED PIPE SEAL
The Flex TPO Molded Pipe Seal is an injection molded, pre-formed flashing for pipes 1” to 6” in diameter. Pipe Seals are packaged in boxes of eight and come with universal clamping rings.

FLEX TPO MOLDED SEALANT POCKET
The Flex TPO Molded Sealant Pocket consists of an interlocking, two-piece, injection molded flexible pocket with a rigid polypropylene vertical wall and pre-formed deck flanges.

6″ TRIM STRIP TPO FLASHING MEMBRANES
The Flex 6” TPO Trim Strip is specifically designed to be used as a strip-in membrane for FlexClad TPO Metal ends and joints, Flex TPO FB Roofing Reinforced Membrane end joint details or for patch installations.

FLEX TPO PRESSURE SENSITIVE PS COVERSTRIP
Flex TPO PS Coverstrip is a .030” thick non-reinforced TPO flashing membrane laminated to a .030” thick cured synthetic rubber pressure sensitive adhesive intended to strip in flat metal flanges such as perimeter edge metal and prefabricated curb flanges.

FLEX TPO PRIMER
Flex TPO Primer is a high solid content, clear (translucent color) polymer-base splice primer used to prepare TPO membrane for improved adhesion to TPO Pressure Sensitive Coverstrip to walls and vertical surfaces prior to installing Flex Self Adhering TPO Membrane.

FLEX TPO SPLIT PIPE BOOTS
Flex TPO Split Pipe-Boots are fabricated flashings made of 45-mil reinforced Flex TPO membrane for pipes 1-inch (25.4 mm) to 6-inches (152.4 mm) in diameter.

FLEX TPO SQUARE TUBE WRAP
Flex TPO Square Tube Wraps are fabricated using 45 mil reinforced Flex TPO membrane. A split and overlap tab are incorporated into these parts to allow the flashings to be opened and wrapped around a square penetration with an obstruction. Manufactured in four sizes: 3”x3”, 4”x4”, 5”x5” and 6”x6”.

FLEX 45 MIL TPO PLUS ROOF MEMBRANE
The Flex 45 TPO Plus polyester reinforced thermoplastic polyolefin (TPO) roofing membranes are designed for use in mechanically fastened and adhered roofing systems. The Flex 45 TPO Plus membrane is manufactured in widths of 5’and 10’ for economical installations.

FLEX 60 TPO PLUS ROOF MEMBRANE
Flex 60 TPO Plus polyester reinforced thermoplastic polyolefin (TPO) roofing membranes are designed for use in mechanically fastened and adhered roofing systems. The Flex 60 TPO Plus membrane is manufactured in widths of 5′ and10’for economical installations.

FLEX 80 TPO PLUS ROOF MEMBRANE
The Flex 80 TPO Plus polyester reinforced thermoplastic polyolefin (TPO) roofing membranes are designed for use in mechanically fastened and adhered roofing systems. The Flex 80 TPO Plus membrane is manufactured in widths of 5’and 10’ for economical installations.

TPO BONDING ADHESIVE
TPO Bonding Adhesive is a high-strength, solvent-based contact adhesive that allows bonding of TPO membrane to various porous and non-porous substrates.

TPO COATED METAL
TPO Coated Metal is a 24-gauge (0.6 mm) galvanized steel sheet that is coated with a layer of .035” non-reinforced TPO flashing. TPO membrane may be welded directly to the coated metal, eliminating the need to strip in the metal with a separate piece of TPO Pressure-Sensitive Cover strip.

TPO CLEAR CUT EDGE SEALANT
TPO Clear Cut-Edge Sealant is a free flowing, translucent polymeric material designed for sealing cut edges (exposed fabric) of SealTite TPO Reinforced Membrane.

TPO FB SUBSTRATE ADHESIVE
TPO FB Substrate Adhesive is a single-component, cold-applied rubberized asphalt emulsion adhesive designed specifically to adhere TPO thermoplastic roof membranes to a variety of compatible substrates.

PO LOW BONDING ADHESIVE
TPO Low VOC Bonding Adhesive is a high-strength solvent-based contact adhesive that allows bonding of TPO membrane to various porous and non-porous substrates.

TPO NON-REINFORCED FLASHING/DETAILING MEMBRANE
TPO non-reinforced flashing/detailing membrane is a 60 mil thermoplastic polyolefin membrane used for inside/outside corners, field fabricated pipe flashings, sealant pockets and scuppers.

TPO OUTSIDE CORNERS
TPO Outside corners are pre-molded and are used for flashing outside corners on a variety of details. Installation is fast and easy with no cutting or stretching required. TPO Outside Corners are used for flashing outside corners on a variety of details.

TPO T-JOINT COVERS
TPO T-Joint Covers are used to seal step-offs at splice intersections. Installation is mandatory on all 60-, 72- and 80-mil TPO systems and on 45-mil systems where step-offs have not been properly sealed.

TPO WALKWAY ROLL
The Viking Products Group TPO Heat-Weldable Walkway Roll is designed to protect the TPO membrane in those areas exposed to repetitive foot traffic and other hazards.

WEATHERED MEMBRANE CLEANER
Weathered Membrane Cleaner is used to clean both new and in-service EPDM membranes and TPO membranes prior to the welding process. It helps to loosen and remove dirt and other contaminants from the surface of the EPDM and TPO membranes and leaves a suitable surface for welding or the subsequent application of Single-Ply Primer Splice Wash.
LOCATIONS
